How To Thread Bobbin Brother

Then put the bobbin and the winder onto the floor. The filled bobbin is then removed and inserted into the bobbin case under the main sewing plate.

Brother Vx 1010 Vx 1020 Sewing Machine Threading Diagram Sewing Machine Manuals Sewing Sewing Machine

Guide the thread through the slit in the needle plate cover.

How to thread bobbin brother. Take the end of the thread from the spool with your right hand. The bobbin on a Brother sewing machine is threaded by placing an empty bobbin on top of the machine and winding it there. Turn the bobbin clockwise by hand until the projection slides into the notch of the bobbin.

Wrap the thread around the bobbin by holding on to the tail end of the thread and pressing on to the foot controller. Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. Draw the thread into the bobbin hole.

Keep doing so for as long as it takes you to fill the bobbin up completely with the thread. The filled bobbin is then removed and inserted into the bobbin case under the main sewing plate. Be sure to wind the thread clockwise around the bobbin otherwise the thread will become wrapped around the bobbin winder shaft.

Place your bobbin inside. Place the spool of thread for the bobbin onto the spool pin. When the presser foot is down the tension is engaged and it will not allow the thread to seat as it should.

Another situation in which you will need to know how to thread a bobbin is when you want to tighten the nuts on your winder. Insert the bobbin with the thread coming from the bottom toward the top and the thread tail hanging out of the bobbin case. Pull the thread through the spring as detailed in the diagram below.

Give a careful look at the mechanism in the area. The bobbin on a brother sewing machine is threaded by placing an empty bobbin on top of the machine and winding it there. Pass the thread toward you by following the grooved line on the thread guide.

1 7 10 cm 2 3 4 to 3 15 16 inches trim the excess thread above the bobbin. Make sure that the thread passes under the pre-tension disk. Wind the thread clockwise around the bobbin 5 or 6 times pass the thread through the guide slit in the bobbin winder seat and then pull the thread to cut it.

Detach the top thread of the sewing machine that goes into the needle. Make sure the spring in the groove is properly catching the thread. To do this put the winder close to a wall and then attach a bolt to the wall.

Make sure you set the bobbin so the thread unrolls in the right direction. The thread should pass through the hole starting from the inside and moving out through. Your machine will automatically stop when the bobbin has been filled.

This is important because it makes the thread enter the tension spring of the bobbin case. If the spool is not positioned so that the thread unwinds correctly the thread may become tangled around the. Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom.

Hold the end of the thread with your left hand and with your right hand wrap the free end of the thread clockwise around the bobbin several times. Pass the thread through the slit in the base of the bobbin seat to trim the excess thread. Clean the surrounding area of the bobbin by following the steps mentioned in the manual.

Bring the end of the thread tail up through the hole in the bobbin. For Brother sewing machines with a fast bobbin-winding system. As long as the presser foot is up the thread can seat properly.

Now detach the bobbin and its case from the machine. The bolt will be able to tighten the nuts without damaging the bobbin or the winder. Pass the end of the thread through the hole on the bobbin from the inside of the bobbin.

Always thread the machine with the presser foot up. Make sure the thread unwinds to the left counterclockwise direction. Only use bobbins that were designed to be used with this machine.

Brother Vx 1120 Sewing Machine Threading Diagram Sewing Machine Brother Sewing Machines Sewing Machine Thread

How To Thread A Brother Sewing Machine Tutorial Brother Sewing Machine Tutorial Sewing Machine Brother Sewing Machines

Pin On Ml S Board Of Coolness

Threading A Brother Sewing Machine Step By Step With Pictures Brother Sewing Machines Sewing Machine Sewing

Brother Vx 1120 Sewing Machine Threading Diagram Sewing Machine Sewing Sewing Hacks